Harley Starter Replacement Of Harley Road King
The procedure of Harley starter replacement for Harley Road King has been laid down in 10 easy steps.
If you are the owner of Harley-Davidson Road King then you should be aware about Harley starter replacement. At first when you notice that your starter is giving you a problem you should remove and inspect it. See if there are any faults in it. Try to clean the starter and reassemble it. In case you are unable to spot the problem you can go through the Harley's manual. You will understand how to repair the starter with the right tools.
However, if you are looking out for Harley starter replacement altogether, then here are simple and step by step instructions:
Begin with removal of Harley starter. The negative battery cable that comes from the terminal of the battery should be turned off before you begin with the replacement process.
Carefully locate the Harley starter's front mounting screw that is on its right side. Remove it with the help of screwdriver. Gently remove the Harley starter from the rear mounting screw.
Locate the nuts, and make sure you remove them carefully when you are on your Harley starter replacement. They will later be needed to join back to the bike.
Next step is to remove the support bracket of exhaust.
In order to get access to hex nut you will have to pull on your rubber boot. Remove the nut from the battery pos. you will also have to remove the main cable of power, positive battery cable and ring terminals.
Now look out for the starter solenoid that is usually at the front of bike's starter. Then remove it.
Find the oil filler cap that is on the right side of bike at the top of transmission case. You will have to rotate it counterclockwise in order to remove it.
Slide the old starter very carefully from the bike through the space that is available between the side cover and the exhaust header pipe. Make sure you do not lose either of the 2 ring dowels.
Lightly oil the bike's O-ring that is on the new starter.
Slide the new starter very cautiously into the bike just like you did it to remove the starter.
These 10 steps might seem to be simple, but a slight mistake and you can bear a huge loss. You cannot afford to miss even a single nut in the bike. Also you need to carefully buy an original Harley starter for the replacement. Any cheap Harley starter replacement can ruin your original bike.
If you are the owner of Harley-Davidson Road King then you should be aware about Harley starter replacement. At first when you notice that your starter is giving you a problem you should remove and inspect it. See if there are any faults in it. Try to clean the starter and reassemble it. In case you are unable to spot the problem you can go through the Harley's manual. You will understand how to repair the starter with the right tools.
However, if you are looking out for Harley starter replacement altogether, then here are simple and step by step instructions:
Begin with removal of Harley starter. The negative battery cable that comes from the terminal of the battery should be turned off before you begin with the replacement process.
Carefully locate the Harley starter's front mounting screw that is on its right side. Remove it with the help of screwdriver. Gently remove the Harley starter from the rear mounting screw.
Locate the nuts, and make sure you remove them carefully when you are on your Harley starter replacement. They will later be needed to join back to the bike.
Next step is to remove the support bracket of exhaust.
In order to get access to hex nut you will have to pull on your rubber boot. Remove the nut from the battery pos. you will also have to remove the main cable of power, positive battery cable and ring terminals.
Now look out for the starter solenoid that is usually at the front of bike's starter. Then remove it.
Find the oil filler cap that is on the right side of bike at the top of transmission case. You will have to rotate it counterclockwise in order to remove it.
Slide the old starter very carefully from the bike through the space that is available between the side cover and the exhaust header pipe. Make sure you do not lose either of the 2 ring dowels.
Lightly oil the bike's O-ring that is on the new starter.
Slide the new starter very cautiously into the bike just like you did it to remove the starter.
These 10 steps might seem to be simple, but a slight mistake and you can bear a huge loss. You cannot afford to miss even a single nut in the bike. Also you need to carefully buy an original Harley starter for the replacement. Any cheap Harley starter replacement can ruin your original bike.
Source...