How To Rebuild A Toilet Tank
How to Rebuild a Toilet Tank
One of the simplest plumbing jobs you can tackle all by yourself is that of replacing the toilet tank. It will take you two hours to complete the entire task with barely any difficulty.
Here's how to do it:
Turn off the water to the toilet tank by turning off the toilet stop or closet stop, which is by the base. Keep turning the handle clockwise until it shuts off.
Drain the tank by pushing the handle down and holding it until the water goes all the way down. Hold the handle until no more water goes down the hole. There will still be about 1" of water in the tank. Wipe all the water out using a sponge.
Use a small adjustable wrench to disconnect the toilet stop nut. Disconnect the tank from the bowl by removing the bolts found inside the bottom of the tank.
Using a large screwdriver to support the head on the bolt and then turn the nut under the tank with an adjustable wrench until it is possible to remove the entire bolt from the tank. Repeat the process on all the bolts.
Carefully align the valve assembly. Gently push through the hole and then turn the locking ring hand tight to make a good seal.
Use large pliers to fully tighten the seal.
Guide the assembly through the hole, then put the tank seal into place that's located on the ball cock and hand tighten the locking nut. Use a small pair of slip-joint pliers to get a more secure fit.
There are 21 pieces to install three tank-to-bowl nuts. Start off with the bolt then slide on a seal. Repeat this process for the other bolts.
It's time for the outside seals. Use the same process as before; squeeze all the rubber seals onto the bolts. Once all the inside and outside seals are in place, slide the brass washers on and lock them into place with thinner nuts. Hand tighten; use an adjustable wrench to secure.
Start with the flexible supply line. It has a heavy-duty seal that should be hand tightened, then use slip-joint pliers a quarter turn. Slide the handle through the hole and then tighten the bolt.
Don't forget to take the overfill tube and place it back into the hole. The overfill tube is what fills up the bowl during the flushing cycle.
Position the tank on top of the bowl. Tighten all of the bolts using small slip-joint pliers and make sure the tank doesn't wobble.
Hold the handle all the way down while the water is filling into the bowl. This will reveal if there are any leaks before the bowl is full of water.
If the seal looks good, let off the handle to allow the bowl to fill up completely. Adjust the water level so it's 1/2" below the fill tube.
One of the simplest plumbing jobs you can tackle all by yourself is that of replacing the toilet tank. It will take you two hours to complete the entire task with barely any difficulty.
Here's how to do it:
Step 1: Turn Off the Water
Turn off the water to the toilet tank by turning off the toilet stop or closet stop, which is by the base. Keep turning the handle clockwise until it shuts off.
Step 2: Drain the Tank
Drain the tank by pushing the handle down and holding it until the water goes all the way down. Hold the handle until no more water goes down the hole. There will still be about 1" of water in the tank. Wipe all the water out using a sponge.
Step 3: Disconnect the Tank
Use a small adjustable wrench to disconnect the toilet stop nut. Disconnect the tank from the bowl by removing the bolts found inside the bottom of the tank.
Using a large screwdriver to support the head on the bolt and then turn the nut under the tank with an adjustable wrench until it is possible to remove the entire bolt from the tank. Repeat the process on all the bolts.
Step 4: Install the Douglas Valve
Carefully align the valve assembly. Gently push through the hole and then turn the locking ring hand tight to make a good seal.
Use large pliers to fully tighten the seal.
Guide the assembly through the hole, then put the tank seal into place that's located on the ball cock and hand tighten the locking nut. Use a small pair of slip-joint pliers to get a more secure fit.
Step 5: Install the Ball cock Assembly
There are 21 pieces to install three tank-to-bowl nuts. Start off with the bolt then slide on a seal. Repeat this process for the other bolts.
It's time for the outside seals. Use the same process as before; squeeze all the rubber seals onto the bolts. Once all the inside and outside seals are in place, slide the brass washers on and lock them into place with thinner nuts. Hand tighten; use an adjustable wrench to secure.
Start with the flexible supply line. It has a heavy-duty seal that should be hand tightened, then use slip-joint pliers a quarter turn. Slide the handle through the hole and then tighten the bolt.
Don't forget to take the overfill tube and place it back into the hole. The overfill tube is what fills up the bowl during the flushing cycle.
Step 6: Reinstall the Tank
Position the tank on top of the bowl. Tighten all of the bolts using small slip-joint pliers and make sure the tank doesn't wobble.
Hold the handle all the way down while the water is filling into the bowl. This will reveal if there are any leaks before the bowl is full of water.
If the seal looks good, let off the handle to allow the bowl to fill up completely. Adjust the water level so it's 1/2" below the fill tube.
Source...