Solving Candle Problems
When making candles, you will, at times, notice that your candles are not perfect from a visual standpoint.
In most situations, the problem may have something to do with the mold.
This article seeks to solve some of the problems that occur while making the candle.
It seeks to find the common mistakes that people make while making candles and gives remedies to these mistakes.
Releasing the mould: A common problem occurs after the wax has dried up.
Separating the mould from the structure tends to be a sensitive task, especially if one is not an expert.
The wax may seem to be attached to the mould, so that any interference may cause the whole thing to collapse.
The simple solution to this is placing the mould inside a freezer for approximately 15 minutes.
The temperature helps the wax to shrink.
After this, the mould is simply tapped and the candle stands on its own.
Another method of releasing the wax from the mould is by first spreading some silicon spray around it.
This is done before the wax is poured into the mould.
Nevertheless, this increases the expenses.
Appearance of wax on the side: This happens due to the following reason.
Whenever the wax is being cooled, there is always a well left over at its bottom.
This well is usually filled over by some natural wax.
The problem sets in when the well is over-filled.
Whenever this happens, one will notice that the well slides down the inner part of the mould.
One should be careful about the amount of "filling" he places on the well.
The Pitted surface: The pitted surface is an indication that the temperature at which the wax was placed into the mould was too low.
The solution out of this problem is to get a thermometer and constantly check the temperature as pouring is done.
There are sites that tell about the temperatures to use for every type of wax.
The Air Bubbles: The presence of air bubbles in ones mould is caused by two major things.
Firstly, either the mould was not tapped hard enough while about to be removed.
Secondly, the air bubbles might be caused by pouring in the wax too fast into the mould.
This may be the major cause of air bubbles.
Some of these problems can be avoided by being careful to follow instructions to detail.
This will save the project a whole lot of disappointment and losses.
In most situations, the problem may have something to do with the mold.
This article seeks to solve some of the problems that occur while making the candle.
It seeks to find the common mistakes that people make while making candles and gives remedies to these mistakes.
Releasing the mould: A common problem occurs after the wax has dried up.
Separating the mould from the structure tends to be a sensitive task, especially if one is not an expert.
The wax may seem to be attached to the mould, so that any interference may cause the whole thing to collapse.
The simple solution to this is placing the mould inside a freezer for approximately 15 minutes.
The temperature helps the wax to shrink.
After this, the mould is simply tapped and the candle stands on its own.
Another method of releasing the wax from the mould is by first spreading some silicon spray around it.
This is done before the wax is poured into the mould.
Nevertheless, this increases the expenses.
Appearance of wax on the side: This happens due to the following reason.
Whenever the wax is being cooled, there is always a well left over at its bottom.
This well is usually filled over by some natural wax.
The problem sets in when the well is over-filled.
Whenever this happens, one will notice that the well slides down the inner part of the mould.
One should be careful about the amount of "filling" he places on the well.
The Pitted surface: The pitted surface is an indication that the temperature at which the wax was placed into the mould was too low.
The solution out of this problem is to get a thermometer and constantly check the temperature as pouring is done.
There are sites that tell about the temperatures to use for every type of wax.
The Air Bubbles: The presence of air bubbles in ones mould is caused by two major things.
Firstly, either the mould was not tapped hard enough while about to be removed.
Secondly, the air bubbles might be caused by pouring in the wax too fast into the mould.
This may be the major cause of air bubbles.
Some of these problems can be avoided by being careful to follow instructions to detail.
This will save the project a whole lot of disappointment and losses.
Source...